Cisco Certified Internetwork Expert – CCIE – Part 3

CCIE MCQ Techhyme

The CCIE Certification is the highest level of achievement for network professionals, certifying an individual as an expert or master. Cisco Systems has since become an unrivaled worldwide leader in networking for the Internet. Its networking solutions can easily connect users who work from diverse devices on disparate networks. Cisco products make it simple for people to access and transfer information without regard to differences in time, place, or platform.

The below listed questions are intended to help you continue on your exciting path toward obtaining your CCIE (Cisco Certified Internetwork Expert) certification. Before looking these questions, it is important to know the basic concepts of CCNA and CCNP.

  1. Cisco Certified Internetwork Expert – CCIE – Part 1
  2. Cisco Certified Internetwork Expert – CCIE – Part 2
  3. Cisco Certified Internetwork Expert – CCIE – Part 3
  4. Cisco Certified Internetwork Expert – CCIE – Part 4
  5. Cisco Certified Internetwork Expert – CCIE – Part 5
  6. Cisco Certified Internetwork Expert – CCIE – Part 6
  7. Cisco Certified Internetwork Expert – CCIE – Part 7
  8. Cisco Certified Internetwork Expert – CCIE – Part 8
  9. Cisco Certified Internetwork Expert – CCIE – Part 9
  10. Cisco Certified Internetwork Expert – CCIE – Part 10
  11. Cisco Certified Internetwork Expert – CCIE – Part 11
  12. Cisco Certified Internetwork Expert – CCIE – Part 12
  13. Cisco Certified Internetwork Expert – CCIE – Part 13
  14. Cisco Certified Internetwork Expert – CCIE – Part 14
  15. Cisco Certified Internetwork Expert – CCIE – Part 15
  16. Cisco Certified Internetwork Expert – CCIE – Part 16
  17. Cisco Certified Internetwork Expert – CCIE – Part 17
  18. Cisco Certified Internetwork Expert – CCIE – Part 18
  19. Cisco Certified Internetwork Expert – CCIE – Part 19

These articles covers everything you need to pass the CCIE Routing and Switching written exam. Each article contains a set of testing questions along with their answer and explanation.

This article covers: Configuration and IOS management commands.

1. When a router is first booted, where is the IOS loaded from by default?

  1. Boot rom
  2. NVRAM
  3. Flash
  4. Rom

Answer – C
Explanation – Flash memory is used by default on all Cisco routers to hold the IOS.

2. Which command is used to set flash memory from two partitions of 8MB to one partition of 16MB?

  1. set partition 16 1
  2. delete partition 1 16
  3. partition flash 1 16
  4. flash partition 1 16

Answer – C
Explanation – The global configuration command is partition flash [flash number] [size of partition].

3. Which VTY command restricts user access?

  1. access-list
  2. access-class
  3. null 0
  4. access-group

Answer – B
Explanation – The command access-class [list-number] is used under the line vty [first-number] [last-number] to add an access list to the VTY lines.

4. Which command will give you the same information as the sh cdp entry * command?

  1. sh cdp neighbor detail
  2. sh cdp entry all
  3. sh cdp neighbor
  4. show cdp traffic

Answer – A
Explanation – The show cdp neighbor detail and show cdp entry * are the same command

5. Which command shows you the neighboring device ID, the local interface, holdtime, capability, platform and port ID of neighboring routers and switches?

  1. sh cdp neighbor detail
  2. sh cdp entry all
  3. sh cdp neighbor
  4. show cdp traffic

Answer – C
Explanation – The show cdp neighbor command provides needed information about all directly connected Cisco devices. However, this command will not provide the IP address of any device.

6. Which configuration register setting will boot the router to ROM Monitor Mode?

  1. 0x2100
  2. 0x2101
  3. 0x2102
  4. 0x210F

Answer – A
Explanation – The configuration register setting of 0x2100 will tell the router to boot from ROM.

7. Which configuration register setting will tell the router to use the boot command specified in NVRAM?

  1. 0x2100
  2. 0x2101
  3. 0x2102
  4. 0x210F

Answer – C, D
Explanation – The configuration register setting of 0x2102F tells the router to boot the IOS from flash and load the configuration from NVRAM.

8. Which configuration register setting will boot an IOS image store on the system ROM (if available)?

  1. 0x2100
  2. 0x2101
  3. 0x2102
  4. 0x210F

Answer – B
Explanation – The configuration register setting 0x2101 will tell the router to boot an IOS from ROM.

9. Which global configuration command will turn off CDP for the entire router?

  1. no cdp enable
  2. no cdp run
  3. no config cdp
  4. cdp off

Answer – B
Explanation – The global configuration command no cdp run will turn off CDP for the entire Cisco device.

10. If you are in Privileged Mode and want to return to User Mode, which command do you use?

  1. Exit
  2. Quit
  3. Disable
  4. Ctrl+Z

Answer – C
Explanation – The command disable will take you from privilege mode to User Mode.

11. Which editing command will move your cursor to the beginning of the line?

  1. Ctrl+E
  2. Ctrl+F
  3. Ctrl+B
  4. Ctrl+A

Answer – D
Explanation – The keystrokes Ctrl+A will move the cursor to the beginning of the line.

12. Which editing command will move your cursor to the end of the line?

  1. Ctrl+E
  2. Ctrl+F
  3. Ctrl+B
  4. Ctrl+A

Answer – A
Explanation – The keystrokes Ctrl+E will move the cursor to the end of the line.

13. Which editing command will move your cursor forward one character?

  1. Ctrl+E
  2. Ctrl+F
  3. Ctrl+B
  4. Ctrl+A

Answer – B
Explanation – The keystrokes Ctrl+F will move the cursor forward one character.

14. Which command will show you the IOS version currently running on your router?

  1. show flash
  2. show flash file
  3. show ip flash
  4. sh ver

Answer – D
Explanation – The command show flash will show you all the files in flash, but the command show version will show you the currently running file.

15. Which command will show you the contents of the EEPROM in your router?

  1. show flash
  2. show flash file
  3. show ip flash
  4. sh ver

Answer – A
Explanation – The flash memory is an EEPROM. The command show flash will show you all the files in flash memory.

16. Which of the following command will load an IOS image from a tftp host?

  1. load flash tftp 172.16.30.2 IOS_Name
  2. copy tftp flash IOS_Name 172.16.10.2
  3. boot system flash 172.16.30.2 IOS_Name
  4. boot system tftp IOS_Name 172.16.10.2

Answer – D
Explanation – Load, not copy is what the question asks. Boot system flash[ios-name][ip-address] is the command used to load an IOS from a tftp host.

17. Which command will show you if a DTE or DCE cable is plugged into serial 0?

  1. sh int s0
  2. sh int serial 0
  3. sho controllers s 0
  4. sho s0 controllers

Answer – C
Explanation – The command show controllers s 0 will show you if the cable is a DTE or DCE cable connection.

18. Which command will stop console messages from writing over the command you are trying to type in?

  1. no logging
  2. logging
  3. logging asynchronous
  4. logging synchronous

Answer – D
Explanation – The global configuration command logging synchronous will stop console messages from writing over the command that you are typing in.

19. Which command will allow users to telnet into a router and not be prompted with a User Mode password?

  1. login
  2. no login
  3. You can be default, not command needed
  4. no password

Answer – B
Explanation – The command no login allows users to telnet into a router without a User Mode password.

20. Which command will set your console to time out after one only one second?

  1. timeout 1 0
  2. timeout 0 1
  3. exec-timeout 1 0
  4. exec-timeout 0 1

Answer – D
Explanation – The console command exec-timeout [minute][second] is used to set the timeout of a session.

Leave a Reply